frequency qen05 smd 5x3.2 xo ? communications equipment a pplication specifica tio n (re v -c) electrical characteristics ...................................................... p01 mechanical characteristics ................................................... p02 ordering information ............................................................. p03 suggested reflow soldering profile ...................................... p03 tape drawing ........................................................................ p04 reel drawing ........................................................................ p04
qen05 smd 5x3.2 xo ? communications equipment application specifica tio n (rev -c ) de cemb er 1 5 th , 2005 1 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy electrical characteristics electrical pa rameters unit minimum ty pi c a l maximum test c onditi ons freque nc y r a nge (see note 1) m h z 1 . 5 4 4 1 2 5 outpu t logic hcmos / ttl output opera t ing te mperatu r e range (see table 1) c -10 to +70 -40 to +85 refer to ordering information storag e tem p erature range c -55 +12 5 po w e r suppl y v o ltage (vcc) v +1. 8 +5. 0 refer to ordering information frequenc y s t abilit y (see note 2) ppm 25 50 100 refer to ordering information aging (firs t year) ppm 5 ref at 25 c input curr en t (see tabl e 2) ma output load pf 15 30 refer to ordering information duty c y cle (see note 3) % 40/60 refer to ordering information rise & f a ll tim e ns 7 from 10% vcc to 90% vcc start-up tim e ms 10 from 10% vcc to 90% vcc not e 1 : not a ll voltages, lo ads o r stabiliti e s ar e availa ble for freq ue ncy over 70 mhz. not e 2 : inclu de 25 c tolerance, operating tempe r atu r e ra nge, inp u t voltage ch ange, loa d ch ange, first ye ar aging, sho ck and vibratio n. not e 3 : duty cycle 4 5 /55% is available o n option. t a b l e 1 : stab ility co d es 2 5 ppm 5 0 ppm 100p p m -10 to + 70c c b a - 40 to + 85c g f d ta ble 2 : i nput curre nt vcc= 5v vcc= 3.3v vcc= 2.5v vcc= 1.8v fre que ncy ra nge (mhz) cl= 15 p f cl=1 5 pf cl=1 5 pf cl=1 5 pf 1.544 to 9.99 9 15 m a 8 m a 7 m a 6 m a 10.00 to 34.9 9 9 20 m a 10 m a 8 m a 7 m a 35.00 to 49.9 9 9 35 m a 25 m a 20 m a 15 m a 50.00 to 12 5 40 m a 35 m a 30 m a 25 m a
qen05 smd 5x3.2 xo ? communications equipment application specifica tio n (rev -c ) de cemb er 1 5 th , 2005 2 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy ? mechanical characteristics suggest ed pad pin co nn ection s #1 t r i state #2 ground #3 outp ut #4 + v cc tri s t a t e func tion pin #1 output (pin # 3 ) open ac t i ve ?1? ac t i ve ?0? high z bottom view hm ax = 1.3 mm top view ma rk ing line 1 ma nufa c t uring c ode + 0 5 + s t a b ility / s uppl y v o lta g e / output c ode line 2 fre que ncy in mhz (6 digits ) example for qen05b da / 50mhz line 1 : g05b da line 2 : 50.00 0
qen05 smd 5x3.2 xo ? communications equipment application specifica tio n (rev -c ) de cemb er 1 5 th , 2005 3 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy ordering information part n u m b e rin g system qen05 b d a r 50.00 0mhz pack ag e t y p e temperature stability supply vo ltag e outp ut outp ut symmetry optio n nominal fre que ncy (mhz) smd pack ag e qen05 : smd 5x3.2 a : 10 0ppm vs -10 to +7 0 c b : 50p pm vs -10 to +70 c c : 25ppm vs -10 to +70 c d : 100 ppm vs -40 to +85 c f : 50ppm vs -40 to +8 5 c g : 25ppm vs -40 to +85 c a : + 5.0v d : +3.3v m : +2.5v n : +1.8v a : hcmos 15pf b : hcmos 30pf blank : 40/60 % r : 45/55% pleas e enter th e nomi nal freq ue nc y suggested reflow soldering profile
qen05 smd 5x3.2 xo ? communications equipment application specifica tio n (rev -c ) de cemb er 1 5 th , 2005 4 teme x r e se rv es th e r i g h t to mo di fy her ei n spe c i f i c a t i o n s an d in form a t i o n s a t any time w hen ne ce ssa r y to pr ov ide o p t im u m per form a n ce an d c o st. freque ncy tape drawing item code dimension toleranc e pitc h of c o mp one nts p 8.0 0.1 pitc h of s p roc k e t hole po 4.0 0.1 le ngth from h o le c e n te r to c o mpone nt c e nte r p1 2.0 0.1 widt h of c a rri e r ta pe w 12.0 0.3 widt h of a dhe s i v e ta pe w0 5.5 0.1 he ight of c o m pone nt ho le a 5.7 0.1 diamet er o f sp ro cket h o l e do ? 1.5 0.1 t o t al o f tap e th ickn ess k 1.5 0.1 reel drawing multiple : 1 k p c s p e r reel unit : mm
|
